10) Specifications  ^

 - Control Section
 - External Signal Processor
 - Patch Panel Section

 Control Section ^

1.	Keyboard	C ~ C, 37 Keys / (3 octaves)
2.	Voltage controlled oscillator 1 (VCO 1)	Scale [32', 16', 8', 4'] / (6 octaves + 6 octaves (FM))  Wave form ( , PW ( ), white noise) / (4 modes)
		PW adjust
3.	Voltage controlled oscillator 2 (VCO 2)	Scale [16', 8', 4', 2'] / (6 octaves + 6 octaves (FM))  Wave form ( , , , Ring Modulator / (4 modes)
		Pitch/ (+- 1octave)
4.	VCO master control	Master tune/ (+-1/2octaves)
		Portamento
		Frequency Modulation intensity by MG/T.EXT
		Frequency Modulation intensity by EG1/EXT
5.	VCO mixer	VCO-1 level
		VCO-2 level
6.	Voltage Controlled High Pass Filter	Cutoff frequency
		Peak [flat ~ self-OSC]
		Cutoff Frequency Modulation intensity by MG/T.EXT
		Cutoff Frequency Modulation intensity by EG2/EXT
7.	Voltage Controlled Low Pass Filter	Cutoff frequency
		Peak [flat ~ self-OSC]
		Cutoff Frequency Modulation intensity by MG/T.EXT
		Cutoff Frequency Modulation intensity by EG2/EXT
8.	Envelope generator 1	Delay time
		Attack time
		Release time
9.	Envelope generator 2	Hold time
		Attack time
		Decay time
		Sustain level
		Release time
10.	Modulation generator	Wave form ,
		Frequency
11.	Manual controller	Control wheel
		Momentary switch
12.	P. switch & volume	Volume
13.	Indicator	LED (trigger, MG rate)

External Signal Processor ^

v

1.	Control section	Input signal level
		Low cut frequency
		High cut frequency
		CV adjust
		Threshold level
2.	Input & output	Signal in (auto-pad system)
		Amplifier out / 0V ~ +8V
		Band pass filtered out
		CV out (F/V) / 0 ~ +8V
		ENV out / 0 ~ +5V
		Trig out /
3.	Indicator (LED)	Peak indicator
		Trigger indicator

Patch Panel Section ^

1.	Keyboard	Keyboard control voltage output (exponential) / 0 ~ +8V
		Keyboard trigger output /
2.	VCO	VCO 1 + VCO 2 control voltage input (linear response) / 0V ~ +8V
		VCO 2 control voltage input (linear response) / 0V ~ +8V
		VCO 1 + VCO 2 external frequency control input (OCT/V) / -3V ~ +3V
3.	VCF	External signal input / 3Vp-p
		External HP filter cutoff frequency control input (2OCT/V) / -5V ~ +5V
		External LP filter cutoff frequency control input (2OCT/V) / -5V ~ +5V
4.	VCO + VCF	Total external modulation input (T.EXT) / -5V ~ +5V
5.	VCA	Initial gain control input / 0V ~ +5V
6.	EG	EG 1 envelope signal normal output / -5V > 0V
		EG 1 envelope signal reverse output / +5V > 0V
		EG1 + EG2 trigger input /
		EG1 + trigger input /
		EG2 envelope signal reverse output /
7.	MG	Triangle output () / 5VPP
		Rectangle output () / 0  +5V
8.	Noise generator	White noise output / 5Vp-p
		Pink noise output / 5Vp-p
9.	Sample and hold	Clock trigger input /
		Sample signal input / 5Vp-p
		S/H output / 5Vp-p
10.	Modulation VCA	Control voltage input / 0 ~ +5V
		Signal input / -5V ~ +5V
		Signal output / -5V ~ +5V
11.	Manual controller	Control wheel output / -5V ~ 0V ~ +5V
		Momentary switch /
12.	Signal out	Signal output / 2Vp-p (output impedance 3.5kOhm)
13.	Headphones	Headphones out / (8 Ohm) 120mwatts

Power consumption		10 watts
Dimensions		569 (W) x 309 (D) x 249 (H) mm
Weight		7.7 kgs
Accessories		Patch cord, connecting cord / 35cm x 2, 3m x 1
Optional equipment		Stand, case